你现在的位置:

S213焊丝/上海斯米克S213焊丝

S213焊丝/上海斯米克S213焊丝上海斯米克S213磷青铜焊丝  标准: 符合GB SCu5210 相当AWS ERCuSn-A  说明: S213是含锡

  • 产品单价: 150.00元/千克
  • 品牌名称:

    斯米克

  • 产地:

    河南 新乡市

  • 产品类别:

    焊条

  • 有效期:

    长期有效

  •  
留言询价 加入收藏
该企业其他产品更多»
S213焊丝/上海斯米克S213焊丝
¥150.00 1056人浏览

S213焊丝/上海斯米克S213焊丝

推荐
上海斯米克L302银焊条_25%银焊条
¥150.00 959人浏览

上海斯米克L302银焊条_25%银焊

推荐
18%银焊条|斯米克18%银焊条|上海18%银焊条
¥150.00 879人浏览

18%银焊条|斯米克18%银焊条|上

推荐
斯米克L303F银焊条、45%银焊条、BAg-5银焊条
¥150.00 387人浏览

斯米克L303F银焊条、45%银焊条

推荐
S911镍铜焊丝|斯米克S911焊丝|ERNiCu-7焊丝
¥150.00 721人浏览

S911镍铜焊丝|斯米克S911焊丝|

推荐
  • 产品详情
  • 网友评价

产品参数

型号: S213焊丝/上海斯米克S213焊丝 品牌: 斯米克
起订: 供货总量:
发货期限: 自买家付款之日起 7 天内发货 所在地: 河南 新乡市
有效期至: 长期有效 品牌:斯米克

详情介绍

S213焊丝/上海斯米克S213焊丝

上海斯米克S213磷青铜焊丝 
 标准: 
符合GB SCu5210 
相当AWS ERCuSn-A 
 说明: 
S213是含锡约8%、含磷不大于 0.4%的磷青铜焊丝。塑性好,锡的加入,
提高了焊缝金属的耐磨性,焊接工艺性能良好。 
 用途: 
适用于紫铜、黄铜、磷青铜等及异种金属的氩弧焊,钢、铸铁的焊补和堆焊。 
 焊丝化学成分(%) 
P Sn Cu 
0.1~0.4 7.5~8.5 余量 
 供应规格(mm): 
盘装Φ 0.6 0.8 0.9 1.0 1.2 1.5 
焊丝直径Φ(长度:1000) 1.5 2.0 2.5 3.0 4.0 5.0 6.0 
 注意事项: 
1. 焊前必须清除工件焊接边缘及焊丝表面的氧化物、油污等污物,以免引起
气孔,夹渣等缺陷,使焊缝性能降低。 
2. 锡的加入扩大了固、液相之间的温度范围,为了减少热脆倾向,以小熔池、
快速焊为宜。 
3. 钨极气体保护焊时,工件要求预热,仅用平焊位置施焊。


Hardfacing

S 101 斯米克焊丝

C3 Cr28 Ni4
Si3.5 Fe Rem.

HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump.
HRc48-54,耐磨、耐气蚀、抗氧化。堆焊铲斗齿,泵套

S 111斯米克焊丝

C1 Cr29 W5
Co Rem.

HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve.
HRc38-47,高温下耐磨、耐蚀。堆焊高温高压阀门

ECoCr-A

S 112斯米克焊丝

C1.5 Cr29 W8
Co Rem.

HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass.
HRc45-50,高温下耐磨、耐蚀。堆焊阀门,热轧孔型

ECoCr-B

S 113斯米克焊丝

C2.5 Cr30 W17
Co Rem.

HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage.
HRc≥55,高温下耐磨、耐热,但抗冲击性差。堆焊螺旋送料机用

S 114斯米克焊丝

C2.5 Cr30 W12
Co Rem.

HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit.
HRc≥53,高温下耐磨、耐热,但抗冲击较差。堆焊牙轮钻头

ECoCr-C

S 201斯米克焊丝

Sn1 Si0.3Mn0.3
Cu Rem.

Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper.
机械性能好,抗裂性好。紫铜气焊及氩弧焊用

ERCu

S 211斯米克焊丝

Si3 Mn1
Cu Rem.

Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel.
机械性能好,铜合金氩弧焊及钢的MIG钎焊用

ERCuSi-Al

S 212斯米克焊丝

Sn5 Cu Rem.

Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用

ERCuSn-A

S 213斯米克焊丝

Sn8 Cu Rem.

Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用

ERCuSn-C

S 214斯米克焊丝

Al7.5 Cu Rem.

Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用

ERCuAl-A1

S 215斯米克焊丝

Al9 Cu Rem.

Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用

ERCuAl-A2

S 221斯米克焊丝

Cu60 Sn1 Si0.3
Zn Rem.

Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约890℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

S 221F斯米克焊丝

Cu60 Sn1 Si 0.3
Zn Rem.

S221 welding rod coated with flux.
外涂焊剂的S221焊丝

S 222斯米克焊丝

Cu58Sn0.9Si0.1
Fe0.8 Zn Rem.

Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约880℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

RBCuZn-C

S 222F斯米克焊丝

Cu58Sn0.9Si0.1
Fe0.8 Zn Rem.

S222 welding rod coated with flux.
外涂焊剂的S222焊丝

RBCuZn-C

S 223斯米克焊丝

Cu59 Sn0.6
Zn Rem.

Melting point is about 900℃. Braze welding of copper, steel and cast iron.
熔点约900℃。铜、钢、铸铁钎焊用

RBCuZn-A

S 224斯米克焊丝

Cu62 Si0.5
Zn Rem.

Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约905℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

S 225斯米克焊丝

Cu48 Ni10
Zn Rem.

Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys.
熔点约935℃。高强度,钎焊钢、镍及硬质合金用

RBCuZn-D

S 225F斯米克焊丝

Cu48 Ni10
Zn Rem.

S225 welding rod coated with flux.
外涂焊剂的S225焊丝

RBCuZn-D

S 226斯米克焊丝

Cu60 Sn0.3
Si0.2 Zn Rem.

Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron.
熔点约900℃。黄铜气焊用,也可钎焊铜、钢、铸铁

S 227斯米克焊丝

Cu58Sn0.9Ni0.5
Si0.1 Fe0.8
Zn Rem.

Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点880℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

RBCuZn-B

S 229斯米克焊丝

Cu55 Ni6 Mn4
Zn余

Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide.
熔点约920℃。高强度,钎焊钢、镍及硬质合金用

S 301斯米克焊丝

Al≥99.5

Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum.
塑性好、耐蚀。纯铝气焊、氩弧焊用

ER1100

S 311斯米克焊丝

Si5 Al Rem.

Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys.
抗裂性好,通用性大。铝合金气焊、氩弧焊用。不宜用高镁合金

ER4043

S 321斯米克焊丝

Mn1.3 Al Rem.

Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys.
良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用

S 331斯米克焊丝

Mg5 Mn0.4
Al Rem.

Corrosion resistance and high strength. Argon arc welding of aluminum alloys.
耐蚀,强度高。铝合金氩弧焊用

ER5183

Hardfacing

S 101 斯米克焊丝

C3 Cr28 Ni4
Si3.5 Fe Rem.

HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump.
HRc48-54,耐磨、耐气蚀、抗氧化。堆焊铲斗齿,泵套

S 111斯米克焊丝

C1 Cr29 W5
Co Rem.

HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve.
HRc38-47,高温下耐磨、耐蚀。堆焊高温高压阀门

ECoCr-A

S 112斯米克焊丝

C1.5 Cr29 W8
Co Rem.

HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass.
HRc45-50,高温下耐磨、耐蚀。堆焊阀门,热轧孔型

ECoCr-B

S 113斯米克焊丝

C2.5 Cr30 W17
Co Rem.

HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage.
HRc≥55,高温下耐磨、耐热,但抗冲击性差。堆焊螺旋送料机用

S 114斯米克焊丝

C2.5 Cr30 W12
Co Rem.

HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit.
HRc≥53,高温下耐磨、耐热,但抗冲击较差。堆焊牙轮钻头

ECoCr-C

S 201斯米克焊丝

Sn1 Si0.3Mn0.3
Cu Rem.

Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper.
机械性能好,抗裂性好。紫铜气焊及氩弧焊用

ERCu

S 211斯米克焊丝

Si3 Mn1
Cu Rem.

Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel.
机械性能好,铜合金氩弧焊及钢的MIG钎焊用

ERCuSi-Al

S 212斯米克焊丝

Sn5 Cu Rem.

Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用

ERCuSn-A

S 213斯米克焊丝

Sn8 Cu Rem.

Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用

ERCuSn-C

S 214斯米克焊丝

Al7.5 Cu Rem.

Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用

ERCuAl-A1

S 215斯米克焊丝

Al9 Cu Rem.

Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用

ERCuAl-A2

S 221斯米克焊丝

Cu60 Sn1 Si0.3
Zn Rem.

Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约890℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

S 221F斯米克焊丝

Cu60 Sn1 Si 0.3
Zn Rem.

S221 welding rod coated with flux.
外涂焊剂的S221焊丝

S 222斯米克焊丝

Cu58Sn0.9Si0.1
Fe0.8 Zn Rem.

Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约880℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

RBCuZn-C

S 222F斯米克焊丝

Cu58Sn0.9Si0.1
Fe0.8 Zn Rem.

S222 welding rod coated with flux.
外涂焊剂的S222焊丝

RBCuZn-C

S 223斯米克焊丝

Cu59 Sn0.6
Zn Rem.

Melting point is about 900℃. Braze welding of copper, steel and cast iron.
熔点约900℃。铜、钢、铸铁钎焊用

RBCuZn-A

S 224斯米克焊丝

Cu62 Si0.5
Zn Rem.

Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约905℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

S 225斯米克焊丝

Cu48 Ni10
Zn Rem.

Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys.
熔点约935℃。高强度,钎焊钢、镍及硬质合金用

RBCuZn-D

S 225F斯米克焊丝

Cu48 Ni10
Zn Rem.

S225 welding rod coated with flux.
外涂焊剂的S225焊丝

RBCuZn-D

S 226斯米克焊丝

Cu60 Sn0.3
Si0.2 Zn Rem.

Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron.
熔点约900℃。黄铜气焊用,也可钎焊铜、钢、铸铁

S 227斯米克焊丝

Cu58Sn0.9Ni0.5
Si0.1 Fe0.8
Zn Rem.

Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点880℃。黄铜气焊及碳弧焊用,也可钎焊铜、钢、铸铁

RBCuZn-B

S 229斯米克焊丝

Cu55 Ni6 Mn4
Zn余

Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide.
熔点约920℃。高强度,钎焊钢、镍及硬质合金用

S 301斯米克焊丝

Al≥99.5

Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum.
塑性好、耐蚀。纯铝气焊、氩弧焊用

ER1100

S 311斯米克焊丝

Si5 Al Rem.

Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys.
抗裂性好,通用性大。铝合金气焊、氩弧焊用。不宜用高镁合金

ER4043

S 321斯米克焊丝

Mn1.3 Al Rem.

Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys.
良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用

S 331斯米克焊丝

Mg5 Mn0.4
Al Rem.

Corrosion resistance and high strength. Argon arc welding of aluminum alloys.
耐蚀,强度高。铝合金氩弧焊用

ER5183


网友评价 0条 [查看全部]