| 起订: 1000 8.5元 | 供货总量: |
| 发货期限: 自买家付款之日起 天内发货 | 所在地: 江苏 无锡市 |
| 有效期至： 长期有效 | 品牌： |
详情介绍
ENGINEERING SPECIFICATION
Model：YHSW-050100V
General
The specification defines the performance characteristics of a5W Continial, Single Output level switching power supply for+5V, 1Amax . The power supply has designed highly reliable but meet internation safety and radiation requirements.]
1.0 Input requirements
1.1 Input voltage range
Type | Voltage range |
Nominal | 230VAC |
Minimum | 100VAC |
Maximum | 240VAC |
Frequency | 47-63 Hz sine wave 1φ |
1.2 Input Current
0.25Arms max | At 100VAC input and DC output full load |
1.3 Input protection
AnadequateinternalfuseontheACinputlineisprovided. |
1.4 Input surge current
30A max | At power supply cold start, ambient temperature 25℃@230Vac nominal AC input |
1.5 Efficiency
65%min | At AC nominal input @ output full load |
1.6 Power consumption
0.3Wrms max | At AC nominal input @ output unload |
AC-DC POWER ADAPTER
ENGINEERING SPECIFICATION
Model：YHSW-050100V
2.0 Output requirements
2.1 Turn on delay
1000ms max | At AC low line input @ output full load |
*Test on delay is measured from 0 voltage output to the main output regulation.
2.2 DC output regulation
Voltage | Loading(A) | ToleranceRange | AdjustablevoltageRange |
MinNormalMax | Total Regulation | ||
+5V | 0A 1A | ±5% | None |
* Total regulation involve line regulation load regulation cross regulation---etc
* Line regulation is measured from 100Vac to 240Vac
* Load regulation is measured all output from min load to max load at 230Vac
nominal AC input voltage.
2.3 Ripple/noise *
Voltage (DC) | Ripple/ Noise(p-p) |
+5V | 80mV |
* The ripple is measured from peak to peak with band width limit of 20MHZ
(By passed at the end of connector with 10uf electrolytic and 0.1μceramic disk
capacitor under DC output full load, AC nominal input 25℃ambient temperature).
2.4 Output transient response(dv,dtmx)
0.5v dc max | At AC nominal input loading from 50% load to full load. |
15ms t max | Dynamic rise time 10us max, duty 40ms max , Dynamic load step is slew rate of 0.5A/us |
*Test only for main output or designed by customer.
2.5Burn in test : Will be defined after meeting.
AC-DC POWER ADAPTER
ENGINEERING SPECIFICATION
Model：YHSW-050100V
3.0 Protection
3.1 Short protection/Over current
The power supply will self-protect any output to ground , And auto recovery when abnormal circuit faults remove .
An output short circuit is defined as any output impedance of less than 0.1 ohms .
Short current and over current can not exceed2Amax . at nominal line input .
4.0 PLD(power line disturbance)
4.1 LINE POWER SURGE
The power supply shall meet its specification with a rise in AC voltage to 120% of maximum rated line voltage (275 voltage for 180-240 Vac operation ) for a maximum of 20 milliseconds at 50Hz. The surge is to be applied five times with an internal of one minute between surges .
4.2 LINE VOLTAGE SAG
The power supply shall continue to meet its specifications with a line voltage drop (and subsequent return to minimum rated voltage)to 145 Vac with a total power sag cycle time of 20 ms (rise and fall time shell equal 10 ms each).
5.0 COOLING
Cooling Method | ||
By mm fan force air cooling |
□ | |
Coolingshallbewithnaturalconvectioncooling | □ |
6.0 EMC standard:CE(EN55022)
7.0 Leakage current:10 mA max .
8.0 Safety standard:CE(EN60950-1)
9.0 HI-POT
PrimaryToSecondary：3000VAC10mA1minuteor4242VDC10mA1minute
PrimaryTOGround： 1500VAC10mA1minuteor2121VDC10mA1minute
10. Environment
10.1 TEMPERATURE AND HUMIDITY
OPERATING TEMPERATURE 0DEGREES C TO 40 DECREES C .
OPERATING HUMIDITY 15% TO 90% RH . (RELATIVE HUMIDITY).
STORAGE TEMPERATURE -20 DEGREES C TO 50 DEGREES C .
STORAGE HUMIDITY 10% TO 95% RH . (RELATIVE HUMIDITY) .
AC-DC POWER ADAPTER
ENGINEERING SPECIFICATION
Model：YHSW-050100V
11. Vibration
SWEEP AND RESONANCE SEARCHFREQUENCY DUARTION AXIS AMPLITUDE
5-20-500 30 MINUTES X , Y, Z G
12. M.T.B.F
Shall be 10000 power on hours on greater under 25 degrees C of ambient temperature MTBF under evaluated under.13. Mechanical
13.1 Dimension unit : (mm)
L×W×H=60 ×39×64mm±213.2 Weight(g) :0.071kg±0.01kg
13.3 Drawing : As Attachment
14.DC output connector type and pin assignment : As attachment
WIRE:24AWG/2C2464,1500m
PLUG:JACKPLUGMINI USB 5PIN
ENGINEERING SPECIFICATION
Model：YHSW-050100V
General
The specification defines the performance characteristics of a5W Continial, Single Output level switching power supply for+5V, 1Amax . The power supply has designed highly reliable but meet internation safety and radiation requirements.]
1.0 Input requirements
1.1 Input voltage range
Type | Voltage range |
Nominal | 230VAC |
Minimum | 100VAC |
Maximum | 240VAC |
Frequency | 47-63 Hz sine wave 1φ |
1.2 Input Current
0.25Arms max | At 100VAC input and DC output full load |
1.3 Input protection
AnadequateinternalfuseontheACinputlineisprovided. |
1.4 Input surge current
30A max | At power supply cold start, ambient temperature 25℃@230Vac nominal AC input |
1.5 Efficiency
65%min | At AC nominal input @ output full load |
1.6 Power consumption
0.3Wrms max | At AC nominal input @ output unload |
AC-DC POWER ADAPTER
ENGINEERING SPECIFICATION
Model：YHSW-050100V
2.0 Output requirements
2.1 Turn on delay
1000ms max | At AC low line input @ output full load |
*Test on delay is measured from 0 voltage output to the main output regulation.
2.2 DC output regulation
Voltage | Loading(A) | ToleranceRange | AdjustablevoltageRange |
MinNormalMax | Total Regulation | ||
+5V | 0A 1A | ±5% | None |
* Total regulation involve line regulation load regulation cross regulation---etc
* Line regulation is measured from 100Vac to 240Vac
* Load regulation is measured all output from min load to max load at 230Vac
nominal AC input voltage.
2.3 Ripple/noise *
Voltage (DC) | Ripple/ Noise(p-p) |
+5V | 80mV |
* The ripple is measured from peak to peak with band width limit of 20MHZ
(By passed at the end of connector with 10uf electrolytic and 0.1μceramic disk
capacitor under DC output full load, AC nominal input 25℃ambient temperature).
2.4 Output transient response(dv,dtmx)
0.5v dc max | At AC nominal input loading from 50% load to full load. |
15ms t max | Dynamic rise time 10us max, duty 40ms max , Dynamic load step is slew rate of 0.5A/us |
*Test only for main output or designed by customer.
2.5Burn in test : Will be defined after meeting.
AC-DC POWER ADAPTER
ENGINEERING SPECIFICATION
Model：YHSW-050100V
3.0 Protection
3.1 Short protection/Over current
The power supply will self-protect any output to ground , And auto recovery when abnormal circuit faults remove .
An output short circuit is defined as any output impedance of less than 0.1 ohms .
Short current and over current can not exceed2Amax . at nominal line input .
4.0 PLD(power line disturbance)
4.1 LINE POWER SURGE
The power supply shall meet its specification with a rise in AC voltage to 120% of maximum rated line voltage (275 voltage for 180-240 Vac operation ) for a maximum of 20 milliseconds at 50Hz. The surge is to be applied five times with an internal of one minute between surges .
4.2 LINE VOLTAGE SAG
The power supply shall continue to meet its specifications with a line voltage drop (and subsequent return to minimum rated voltage)to 145 Vac with a total power sag cycle time of 20 ms (rise and fall time shell equal 10 ms each).
5.0 COOLING
Cooling Method | ||
By mm fan force air cooling |
□ | |
Coolingshallbewithnaturalconvectioncooling | □ |
6.0 EMC standard:ul(55022)
7.0 Leakage current:10 mA max .
8.0 Safety standard: fcc(60950-1)
9.0 HI-POT
PrimaryToSecondary：3000VAC10mA1minuteor4242VDC10mA1minute
PrimaryTOGround： 1500VAC10mA1minuteor2121VDC10mA1minute
10. Environment
10.1 TEMPERATURE AND HUMIDITY
OPERATING TEMPERATURE 0DEGREES C TO 40 DECREES C .
OPERATING HUMIDITY 15% TO 90% RH . (RELATIVE HUMIDITY).
STORAGE TEMPERATURE -20 DEGREES C TO 50 DEGREES C .
STORAGE HUMIDITY 10% TO 95% RH . (RELATIVE HUMIDITY) .
AC-DC POWER ADAPTER
ENGINEERING SPECIFICATION
Model：YHSW-050100V
11. Vibration
SWEEP AND RESONANCE SEARCHFREQUENCY DUARTION AXIS AMPLITUDE
5-20-500 30 MINUTES X , Y, Z G
12. M.T.B.F
Shall be 10000 power on hours on greater under 25 degrees C of ambient temperature MTBF under evaluated under.13. Mechanical
13.1 Dimension unit : (mm)
L×W×H=60 ×39×64mm±213.2 Weight(g) :0.071kg±0.01kg
13.3 Drawing : As Attachment
14.DC output connector type and pin assignment : As attachment
WIRE:24AWG/2C2464,1500m
PLUG:JACKPLUGMINI USB 5PIN
网友评价 共0条 [查看全部]