起订: 1 1100.00元 | 供货总量: |
发货期限: 自买家付款之日起 天内发货 | 所在地: 江苏 常州市 |
有效期至: 长期有效 | 品牌: |
详情介绍
产品说明
BC-346A为一种特制的耐高温绝缘凡立水,且已被广泛的使用于UL CLASS A、B、F
及H等系统中。
产品特点
1. 极佳的延展性与粘着性。 2. 高度的结合力。
3. UL绝缘系统认证至CLASS H等级(180℃)。 4. 通过美国政府认定之产品。
5. 美国国防部核准为MIL-I-24092,CB等级180系列。
产品说明
电气产品与电子零件各类型线圈、马达、发电机、变压器、电枢等
1. 依产品特性决定所需要稀释的浓度。
2. 将欲处理之产品预热到105℃。
3. 冷却至65℃至75℃。
4. 浸没于凡立水中,15-30分钟至气泡消失为止。
5. 将产品滴干15~30分钟。(为使其拥有更强的结合力,滴干时间愈短愈好)
6. 至于烤箱烘烤,以下为建议的烘烤温度及时间。(依产品不同做适当调整)
*2.5-5小时 @ 135℃ *1.5-4小时 @148℃
*1-2小时 @ 162℃
*烘烤时间为产品达到烘烤温度后完全硬化所需之时间
TYPICAL PROPERTIES
Physical
Appearance/Color Clear/Amber
Specific Gravity @700F.,ASTM D-287 19.5-21.5°
Viscosity,.Dolph Cup @86°F 48.0-21.5 sec.
Viscosity,#1 Demmler Cup @86°F 44-55 sec.
Build-Up, D.F.T., ASTM D-115 4-5 mils
Thinner T-100
Bake Time @300°F. on a Strip,ASTM D-115 30 min.
Cure Time @ 300°F. in 20 gram test cup 65 min
Corrosive Effect on Copper None
Chemical Resistance
Water Excellent
Acid (10% Sulfuric Acid) Excellent
Alkali (1% Sodium Hydroxide) Excellent
Salt Water Excellent
Oil. ASTM D-115 Passed
Electrical
Dielectric Strength, volts/mil (dry) 4,000
Dielectric Strength, volts/mil (wet) 2,900
GENERAL PROPERTIES
COMPATIBILITY WITH MAGNET WIRE COATINGS
HI-THERM BC-346A is compatible with the following magnet wire coatings:
Polyamide Epoxy Polyester Amide-Imide
Textile Polyimide Polyvinyl Formal-Polyamide
Polyurethane Amide-Imide Polyurethane-Polyamide
HEAT LIFE
HI-THERM BC-346A has a heat life of 20,000 hours at 215℃.And 40,000 hours at 205℃.As determined by
IEEE#57(Twisted Pairs)using Polyester Amide-Imide wire Data is available on use of BC-346A in UL listed
systems through 220℃
SOLVENT
Thin with DOLPH’S T-100(V.M. & P.Naphtha)
Dolph’s T-200-X(Xylol) may also be used
IMPREGNATING ABILITY
Excellent wetting properties give maximum penetration using atmospheric or vacuum impregnation
DIP TANK STABILITY
Field experience has proved HI-THERM BC-346-A to have excellent dip tank stability.
High temperature (220°C) varnish: tough, flexible, and QPL and UL recognized; meets MIL-I-24092D. Class 180 for processing at land-based facilities. UL systems up to 220°C.
产品说明
BC-359为一支独特为了节省能源及增加生产量所开发需经稀释的凡立水
产品特点
1. 烘烤温度低(110℃)及快速烘干。
2.导线不易碎断。
3. 低成本一需经过稀释使用。
4. 结合力强。
5 .优异的耐化学及耐磨损性。
6.UL绝缘系统认证至CLASS H等级(180℃)
7.极适合自动化作业系统。
8. 符合RULE 66的污染防治标准。
9. 优异的防潮性—即使在潮湿环境下,电介质强度不会改变
产品用途
电气产品与电子零件,各类型线圈、马达、发电机、变压器、继电器、PC电路板等
使用说明
1. 依产品特性决定所需要稀释的浓度。
2. 预热欲处理的产品至胶带平贴,湿气除去为止。
3. 冷却至38℃至54℃。
4. 浸没于凡立水中,10-20分钟至气泡消失为止。
5. 将产品滴干15~20分钟。
6. 至于烤箱烘烤,以下为建议的烘烤温度及时间。(依产品不同做适当调整)
*8-10小时 @ 110℃
*45分钟-2小时 @150℃
*2-4小时 @ 120℃
*30分钟-90分钟 @160℃
*1-3小时 @ 135℃
*烘烤时间为产品达到烘烤温度后完全硬化所需之时间
以下为自动化作业系统所建议处理流程:
1. 依产品特性决定所需要稀释的浓度。
2. 将产品预热至60℃。
3. 浸没于凡立水中15秒。
4. 滴干2-4分钟。
5. 置于烤箱烘烤。
6.烘烤所需时间请参照上述之温度及时间配合表。
TYPICALPROPERTIES
Physical
As Shipped Thinned 25%(by volume) with/T-100
Appearance/Color Clear/Amber Clear/Amber
Specific Gravity @700F.,ASTM D-287 23-27° 30-35°
Viscosity,.Dolph Cup @86°F 56-74 sec. 19-22 sec.
Film Build,mils/side,ASTM D-115 2-2.5 mils 0.25-1 mils
Thinner T-100 T-100
Bake Time @ 2300F. on a Strip,ASTM D-115 30 min. 30 min.
Cure Time @ 2300F. in 20 gram test cup 2hr. 2hr.
Corrosive Effect on Copper None None
Bond Strength on MW-35 Magnet Wire,lbs
@25℃
@150℃
28
3.5
Electrical
Dielectric Strength, volts/mil (dry) 3,000
Dielectric Strength, volts/mil (wet) 3,000
Chemical Resistance
Water Excellent
Acid (10% Sulfuric Acid) Excellent
Alkali (1% Sodium Hydroxide) Excellent
Salt Water Excellent
Oil. ASTM D-115 Passed
稀释
在一般程序下作业时,稀释比例大约为(52:48)(BC-359:释剂)
但请自行依产品特性调整所需之稀释比例。
储存
储存于阴凉干燥的环境(建议18℃~24℃),并远离日光的直接照射
保存期限:一年 于23℃以下温度
nergy-saving, solderable, fast cure/low temperature cure varnish: flexible with superior moisture, chemical, and abrasion resistance. Rule 66 compliant. UL systems up to 200°C.
网友评价 共0条 [查看全部]